管廊用中埋天然橡胶止水带400*10
面板坝GB柔性填料系填在周边缝顶部预留“倒△”形槽内，必须粘紧密实，并呈弧形向上隆起，以便能更好地适应面板变形，在其表面采用聚氯乙烯塑料带包盖密封。死水位以上采用钢片，要用角钢通过螺栓将其嵌固在砼上。面板坝GB柔性填料施工前应先将其与砼结合部位用钢丝刷刷去砼表面的浮皮，，风干后再用。施工准备用钢筋台车将面板坝GB柔性填料、GB防渗盖板、电镀角钢及电镀膨胀螺栓等运至相应的施工部位。嵌缝处理用钢刷将预留“v”槽内两侧清理干净，再用水冲洗槽内外，除去缝面上的灰砂。“V”槽清理干净后自然晾干。面板坝GB柔性填料填缝用黏合剂将槽内、外壁均匀涂刷一遍，外壁要相应涂刷的宽一些，不可漏刷。黏合剂刷好晾1h后，手感快干时，先在槽底沿槽走向放置一条PVC棒。再将面板坝GB柔性填料均匀切成条状压入槽内，并在外壁按设计要求的弧状堆起2cm高。最后用手捶捶紧，嵌填一定要密实。面板坝GB柔性填料嵌填完毕后，要及时盖上防渗盖板，再用冲击钻钻孔，安装电镀角钢后埋设10 x75电镀膨胀螺栓，间距为400mm。利用电镀角钢通过电镀膨胀螺栓将GB防渗盖片嵌固在砼上。
Dam GB flexible filler to fill in the Department of peripheral joint top reserved inverted triangular groove, you must stick with dense, and curved upward, in order to better adapt to the deformation of the panel, on the surface of the PVC plastic tape sealing cover. The steel sheet is used above the dead water level, and the angle steel should be embedded in the concrete with the angle steel through the bolt. GB flexible dam filling construction should be preceded with the concrete binding site to use wire brush on the surface of concrete, puffing, dry and then. The
管廊用中埋天然橡胶止水带400*10
construction is ready to transport the GB flexible packing, GB anti seepage cover plate, electroplating angle steel and electroplating expansion bolt to the corresponding construction site with steel bar trolley. The steel brush will be reserved for the "V" slot on both sides of clean caulking treatment, then rinse tank inside and outside, remove seam on the surface of the sand. The "V" trough is cleaned and dried naturally. The GB flexible filler filler in the panel dam is used to paint the inner and outer walls evenly, and the outer wall should be brushed in a wide range, and the brush can not be leaked. When the adhesive is brushed to dry the 1H, when the feel is dry quickly, a PVC stick is placed at the bottom of the slot at the bottom of the groove. The dam GB flexible uniform filler strips pressed into the groove, and the outer wall of the arc-shaped pile according to the design requirements of 2cm high. At last thump with your hands, and the inlay must be dense. After the completion of the GB flexible fill of the face dam, the impervious cover should be covered in time. Then the drill hole is drilled and the plating angle steel is placed. Then the 10 x75 plating expansion bolt is embedded, and the spacing is 400mm. The GB anti seepage cover is embedded in the concrete by using the electroplated angle steel through the plating expansion bolt.
管廊用中埋天然橡胶止水带400*10
construction is ready to transport the GB flexible packing, GB anti seepage cover plate, electroplating angle steel and electroplating expansion bolt to the corresponding construction site with steel bar trolley. The steel brush will be reserved for the "V" slot on both sides of clean caulking treatment, then rinse tank inside and outside, remove seam on the surface of the sand. The "V" trough is cleaned and dried naturally. The GB flexible filler filler in the panel dam is used to paint the inner and outer walls evenly, and the outer wall should be brushed in a wide range, and the brush can not be leaked. When the adhesive is brushed to dry the 1H, when the feel is dry quickly, a PVC stick is placed at the bottom of the slot at the bottom of the groove. The dam GB flexible uniform filler strips pressed into the groove, and the outer wall of the arc-shaped pile according to the design requirements of 2cm high. At last thump with your hands, and the inlay must be dense. After the completion of the GB flexible fill of the face dam, the impervious cover should be covered in time. Then the drill hole is drilled and the plating angle steel is placed. Then the 10 x75 plating expansion bolt is embedded, and the spacing is 400mm. The GB anti seepage cover is embedded in the concrete by using the electroplated angle steel through the plating expansion bolt.
水闸橡胶密封件，闸门水封 ，水闸止水带，闸门止水橡皮，水闸橡胶密封件，闸门水封 ，水闸止水带，闸门止水橡皮
管廊用中埋天然橡胶止水带400*10
管廊用中埋天然橡胶止水带400*10
Sluice rubber seal, gate water seal, sluice stop water belt, gate water stop rubber, sluice rubber seal, gate water seal, sluice stop water belt, gate water stop rubber.
水闸橡胶密封件，闸门水封 ，水闸止水带，闸门止水橡皮。水闸橡胶密封件用材料分为两类
Water lock rubber seal, gate water seal, water sluice water stop belt, gate water stop rubber. The rubber sealing parts of the sluice are divided into two categories
类：天然橡胶或天然橡胶为主的材料，SF6674适于大型工程闸门。SF6474适于中、小型工程闸门。 Ⅱ类：合成橡胶或合成橡胶为主的材料，SF6574适于水中含有少量酸、碱、油烊或海水的工程闸门。
Class: natural rubber or natural rubber material, SF6674 suitable for large engineering gate. SF6474 is suitable for medium and small engineering gates. Class II: materials of synthetic rubber or synthetic rubber based, SF6574 is suitable for water containing a small amount of acid, alkali, oil or natural water gate project.
河北瑞博橡塑制品有限公司是一家集橡胶支座，橡胶止水带，伸缩缝等工程橡胶制品为主的专业生产企业。欢迎各界朋友莅临参观指导，业务洽谈。欢迎致电：13166570832