中埋式环形橡胶止水带300*6
橡胶止水带和止水橡皮是以天然橡胶与各种合成橡胶为主要原料,掺加各种助剂及填充料,经塑炼、混炼、压制成型，其品种规格较多，有桥型、山型、P型、U型、Z型、乙型、T型、H型、E型、Q型等。根据使用情况又可分类为埋式橡胶止水带和背贴式橡胶止水带。该止水材料具有良好的弹性,耐磨性、耐老化性和抗撕裂性能,适应变形能力强、防水性能好，温度使用范围为-45℃-+60℃.当温度超过70℃,以及橡胶止水带受强烈的氧化作用或受油类等有机溶剂侵蚀时，均不得使用橡胶止水带.二：使用方法 橡胶止水带必需采取可靠的固定措施，绑扎钢筋和支模时。防止在浇注混凝土时发生位移，保证止水带在混凝土中的正确位置。 只能在止水带的允许部位上穿孔打洞，对于固定止水带时。不得损坏止水带有效防水部位。 常用的固定方法有：利用附加钢筋固定；专用卡具固定；用铅丝和模板固定等。不论采用何种固定方法，对于止水带的固定方法应按设计要求的施工规范进行且必需保证止水带定位准确，不损坏止水带有效防水部位，方便混凝土浇捣。
The rubber sealing strip and sealing rubber with natural rubber and various synthetic rubber as the main raw material, and the filling material mixed with various additives, through plasticizing, mixing, molding, the more varieties of different specifications, bridge, mountain type, P type, U type, Z type, T type, H type, type, E type and Q type etc.. According to the use, it can be classified into buried rubber water stop belt and back sticking rubber water stop belt. The sealing material has good elasticity, abrasion resistance, aging resistance and tear resistance to deformation ability, good waterproof performance, temperature range of -45 DEG -+60 DEG. When the temperature exceeds 70 degrees Celsius, and the rubber sealing strip by strong oxidation or by oil and other organic solvent erosion, shall use the rubber sealing belt. Two: how to use the rubber sealing belt fixed reliable measures must be taken, and when binding steel formwork. Prevent the displacement of the concrete in the concrete and ensure the correct position of the water stop in the concrete. Holes can only be perforated on the allowed parts of the water stop, for the fixed water stop belt. The effective waterproof part of the water belt shall not be damaged. Fixed methods are commonly used: the use of additional reinforcement fixation; special fixture fixed with wire and fixed template. No matter what kind of fixation method is adopted, the fixing method of the waterstop should be carried out according to the construction specification of the design requirement, and the location of the sealing belt must be ensured accurately, and the effective waterproof part of the water stop zone is not damaged, so as to facilitate the concrete pouring and tamping.
中埋式环形橡胶止水带300*6
中埋式环形橡胶止水带300*6
按型号可分为：CB型橡胶止水带（埋入式中间有孔型）；CP型橡胶止水带（埋入式中间无孔型）；EB型橡胶止水带（外贴式中间有孔型）；EP型橡胶止水带（外贴式中间无孔型）。 按材质可分为：天然橡胶止水带，氯丁橡胶止水带，三元乙丙橡胶止水带。 按使用情况可分为：中埋式橡胶止水带和背贴式橡胶止水带(外贴式橡胶止水带)、钢边橡胶止水带、遇水膨胀橡胶止水带、平板式止水带。
According to the type, it can be divided into: CB type rubber water stop (embedded intermediate pass), CP type rubber water stop (buried intermediate no pass), EB type rubber water stop (externally attached middle pass), EP type rubber water stop (externally attached middle pass). According to the material, it can be divided into natural rubber water stop belt, chloroprene rubber water stop belt, three ethylene propylene rubber water stop belt. According to the usage, it can be divided into: the buried rubber water stop and the back type rubber water stop (externally attached rubber water stop), the steel side rubber water stop belt, the water swelling rubber water stop belt and the flat type water stop belt.
橡胶止水带主要用于混凝土现浇时设在施工缝及变形缝内与混凝土结构成为一体的基础工程，如地下设施、隧道涵洞、输水渡槽、拦水坝、贮液构筑物等。 遇水膨胀橡胶止水带主要用于混凝土现浇时设在施工缝及变形缝内与混凝土结构成为一体的基工程，如地下设施、隧道涵洞、输水渡槽、拦水坝、贮液构筑物等。：接头方法
The rubber sealing belt is mainly used for cast-in-place concrete when in construction joints and deformation joints and concrete structure has become one of the basic engineering facilities, such as underground tunnels, culverts, dams, aqueducts, liquid storage structures etc.. The rubber sealing belt is mainly used for cast-in-place concrete when in construction joints and deformation joints and concrete structure has become one of the basic project of water swelling, such as underground facilities, tunnel, culvert aqueduct, dam, reservoir structures etc.. Joint method
中埋式环形橡胶止水带300*6
中埋式环形橡胶止水带300*6
橡胶止水带接头方法有两种：一种是采用粘接剂进行冷接头，一种是使用热硫化模具进行热接。 下边就分别介绍下两种接头方法：粘接剂冷接是采用橡胶止水带专用冷接胶水、采用搭接法把止水带需要接头的断面用磨光机磨平5~10厘米、涂胶水压实即可，具有强度高、凝固快的优点、施工方便、省时省力，可达到一般工程质量要求。 现场热接硫化法接头是使用与止水带匹配的热硫化模具及生胶片现场硫化热接，施工难度大，但接头效果理想，适合对工程质量要求严格的项目。
There are two kinds of joint methods for rubber water stop belt: one is to use adhesive for cold joint, the other is to use hot vulcanization mould for hot connection. Below introduces two kinds of adhesive joint method: cold connection is the use of rubber sealing strip with special cold glue, overlapped by the waterstop joints with grinder grinding section to 5~10 cm, glue can be compacted, has high strength, fast solidification has the advantages of convenient, time-saving, can meet the general engineering quality request. The field thermal contact vulcanization joint is a hot vulcanizing mold matched with the water stop belt and the on-site vulcanizing hot bonding of the raw film. The construction is difficult, but the joint effect is ideal, and it is suitable for the project with strict quality requirements.
衡水汉江橡塑科技有限公司是橡胶止水带止水条、天然橡胶、防水涂料，防水卷材等产品专业生产加工的公司，。欢迎各界朋友莅临参观、指导和业务洽谈。欢迎致电：13091176335
衡水汉江橡塑科技有限公司是橡胶止水带止水条、天然橡胶、防水涂料，防水卷材等产品专业生产加工的公司，。欢迎各界朋友莅临参观、指导和业务洽谈。欢迎致电：13091176335